President Richard II 10 Meter Amateur Radio – 50W PEP AM/FM
The President Richard II is an AM/FM mobile amateur radio for licensed operators who want front-panel controls, adjustable noise reduction and a built-in SWR meter. President lists its output as 13W AM carrier, approximately 50W PEP on AM and 40W on FM, with coverage of the 10-meter and 12-meter amateur bands.
The Richard II succeeds the original President Richard. Its larger front panel brings together a seven-color display, front six-pin microphone connection and USB-C charging socket. This is an amateur radio, not a license-free CB radio.
Key features
- NRC noise reduction: Independently adjustable transmit and receive noise reduction, with five levels for each.
- Receiver controls: Automatic Squelch Control, manual squelch, RF gain, ANL, noise blanker and Hi-Cut filtering.
- Transmit controls: Adjustable RF power, microphone gain, talkback and echo.
- SWR and protection: Built-in SWR measurement, SWR protection and voltage protection.
- Display and navigation: Seven-color multifunction LCD, frequency display, VFO mode, scan and scan skip.
- Audio options: VOX, public-address capability, an external-speaker connection and a separate PA-speaker connection.
- Front USB-C charging: A convenient charging socket for compatible devices.
Technical specifications
| Specification | President Richard II |
|---|---|
| Manufacturer reference | TXUS134 |
| Modes | AM and FM; no SSB |
| Frequency coverage | 28.000–29.700 MHz and 24.890–24.990 MHz |
| Manufacturer-listed output | 13W AM carrier; approximately 50W PEP AM; 40W FM |
| Power supply | 13.8V DC, negative ground |
| Listed transmit current draw | 7A |
| Antenna connection | SO-239; 50-ohm antenna system |
| Microphone connection | Front six-pin President wiring |
| Microphone type selection | Electret or dynamic |
| Dimensions, W × D × H | 7.283 × 7.480 × 2.165 inches / 185 × 190 × 55 mm |
| Weight | 2.43 lb / 1.1 kg |
| Front USB-C socket | Device charging |
Planning your installation
Measure the radio opening and allow additional clearance for the mounting bracket, controls, microphone plug and rear connections. Check your installation against the listed dimensions rather than assuming compatibility from the truck make or an existing radio bracket.
Use a properly matched 50-ohm antenna system designed for your intended operating frequencies. A CB antenna's power rating alone does not establish suitability for 10-meter or 12-meter operation. Install and check the antenna system's SWR before transmitting, and recheck it after moving the antenna.
The Richard II requires a suitable 13.8V DC supply. Do not connect it directly to a 24V electrical system.
Complete Richard II kits and combos
Microphone and speaker options
The factory electret UP/DOWN microphone is included. The radio accepts President-wired six-pin electret or dynamic microphones; select the appropriate microphone type in the radio menu.
- President DIGIMIKE six-pin microphone: An optional microphone with adjustable noise reduction for President six-pin radios.
- Driver Extreme DRX-9010 external speaker: An optional external listening speaker with a detachable lead and 3.5mm plugs.
These accessories are sold separately from the main radio. A standard four-pin microphone does not plug directly into the Richard II's six-pin socket.
What's in the box
- Radio: President Richard II AM/FM transceiver.
- Microphone: Electret UP/DOWN microphone and microphone support.
- Mounting hardware: Mounting cradle and screws.
- Power lead: Fused DC power cord.
- Documentation: Owner's manual.
The antenna, antenna mount, coax and external speaker are not included with the main radio. President lists a two-year manufacturer warranty, subject to its warranty terms.
Don't forget to add the Pro tune and alignment option at checkout so that your radio is professionally bench-tuned for best performance per the manufacturer's service manual.
Frequently asked questions
Is the President Richard II a CB radio?
No. The Richard II is a 10-meter and 12-meter amateur radio, not a license-free 40-channel CB radio. Its AM and FM modes do not make it a CB transceiver.
What license do I need to transmit with the Richard II in the United States?
For AM/FM voice operation on the radio's amateur bands, you need General-class privileges or higher, or an existing Advanced-class license, and must use frequencies and modes permitted by your license. Technician-class 10-meter voice privileges are SSB-only; the Richard II does not have SSB.
How much power does the Richard II produce?
President lists 13W AM carrier, approximately 50W PEP on AM and 40W on FM. These are separate mode-specific ratings, not a 50W FM rating.
Does the Richard II have single sideband?
No. It operates in AM and FM and does not include USB or LSB modes.
What are the Richard II's dimensions?
President lists 7.283 inches wide × 7.480 inches deep × 2.165 inches high, or 185 × 190 × 55 mm. Allow extra installation space for brackets, controls and cable connections.
What antenna should I use?
Use a 50-ohm antenna system designed and adjusted for the amateur frequencies you intend to use. Do not assume that a CB antenna covers the entire 10-meter band or the 12-meter band. Check SWR before transmitting.
Which microphone connection does it use?
The Richard II has a front six-pin President microphone connection. It supports compatible electret and dynamic microphones through the microphone-type menu, and includes an electret UP/DOWN microphone.
Does the main radio include an antenna or external speaker?
No. It includes the transceiver, factory microphone and support, mounting cradle and screws, fused power cord and manual. The antenna system and external speaker are separate purchases.
Can the Richard II connect directly to 24V?
No. Its specified supply is 13.8V DC for a suitable negative-ground installation. Do not connect the radio directly to a 24V supply.